How to install a Motorola U6 PEBL Faceplate (Absolute Accessories):
Note: These installation instructions are intended to be a guide; installation should be done very carefully. The installer should have some basic knowledge of taking things apart. Absolute Accessories does not assume any responsibility and advises to the fact of this being a guide.
STEP 1:
Purchase your faceplate from Absolute Accessories! It will look like this (your pattern of choice of course):

STEP 2:
a) Open your Motorola U6 PEBL so that you can see the LCD (front display).
b) Look at your LCD screen. You will notice a panel over the front of the LCD, much like the one you will receive when you purchase your Absolute Accessories faceplate. It will look like this:

The one that comes with the phone will need to come off. This is held on by adhesive tape. You can remove it from your phone with a gentle slow pressure pulling towards you. Some have used a hair dryer to heat the glue and make it easier to remove. You would need to be very careful with the heat and would only want a slight warm to the touch feel.
STEP 3:
You will now see four screws that are visible. These will need to be removed. You will want to use your Absolute Accessories U6 PEBL screwdriver. Be careful not to lose any screws as these will be needed to put the new faceplate on.
STEP 4:
a) Remove the old faceplate. Gently remove the faceplate from the phone.
b) After the old one is off, align the new one and gently snap into place.
c) Screw in the four screws that were removed earlier.
d) Grab your new LCD cover and remove the tape protectant. Align it to the front of the LCD and secure it into place.
STEP 5:
Remove your battery cover by pressing the battery release button on the back. Place your new battery cover into place and lock it in.
YOU'RE DONE!
At Absolute Accessories, we strive to provide as much information as possible to help make your buying experience an easy one! If you felt this guide was helpful, please vote yes below.
Note: These installation instructions are intended to be a guide; installation should be done very carefully. The installer should have some basic knowledge of taking things apart. Absolute Accessories does not assume any responsibility and advises to the fact of this being a guide.
STEP 1:
Purchase your faceplate from Absolute Accessories! It will look like this (your pattern of choice of course):
STEP 2:
a) Open your Motorola U6 PEBL so that you can see the LCD (front display).
b) Look at your LCD screen. You will notice a panel over the front of the LCD, much like the one you will receive when you purchase your Absolute Accessories faceplate. It will look like this:
The one that comes with the phone will need to come off. This is held on by adhesive tape. You can remove it from your phone with a gentle slow pressure pulling towards you. Some have used a hair dryer to heat the glue and make it easier to remove. You would need to be very careful with the heat and would only want a slight warm to the touch feel.
STEP 3:
You will now see four screws that are visible. These will need to be removed. You will want to use your Absolute Accessories U6 PEBL screwdriver. Be careful not to lose any screws as these will be needed to put the new faceplate on.
STEP 4:
a) Remove the old faceplate. Gently remove the faceplate from the phone.
b) After the old one is off, align the new one and gently snap into place.
c) Screw in the four screws that were removed earlier.
d) Grab your new LCD cover and remove the tape protectant. Align it to the front of the LCD and secure it into place.
STEP 5:
Remove your battery cover by pressing the battery release button on the back. Place your new battery cover into place and lock it in.
YOU'RE DONE!
At Absolute Accessories, we strive to provide as much information as possible to help make your buying experience an easy one! If you felt this guide was helpful, please vote yes below.
Guide created: 12/01/06 (updated 11/19/08)
Thank you for voting. If your vote meets our