Simple Installation

   1. Carefully remove paper back.
   2. Starting at one end carefully press decal in to desired position, work out air pockets.
   3. Carefully remove clear covering being careful not to tear the decal.

That simple to install.

General instructions

   1. Clean the area where you will apply this decal
   2. Measure to put on the right place, use tape to hold the top and make sure is ok.
   3. Peel the back
   4. Stick the decal even from side to side or top to bottom. do it even to avoid bubbles.
   5. REMOVE transfer tape.

SURFACE PREPARATIONS

All Surfaces must be cleaned. WAX MUST BE REMOVED COMPLETELY, even if the area (boat, motorcycle, car, truck, or other) is new. Rubbing compound contains wax, therefore it must also be removed. To remove wax, use ammonia, Windex or acetone. Acetone is not recommended for painted areas.

APPLICATION

1. You will need masking tape, spray bottle, Joy or dish washing liquid, and a tape measure.
2. Using the masking tape to underline where you want to place the vinyl sign. If you have letters that drop below the line, remove tape in that area.
3. With you spray bottle, mix a solution of 20 drops of Joy, Ivory, etc in one pint of water. Carefully spray the soapy water on the area where you want to place the vinyl.
4. Place the Graphics face down and peel away the waxed paper backing. Then spray the solution on the back of the vinyl sign. Be sure the Graphics is adhering to the application tape (premask).
5. While the area is still very wet, place the Graphics in the selected position. The soapy water allows you to slide Graphics into place. Gently rub palm over Graphics. (The water has no bearing on the adhesion; it is only for positioning the Graphics and removing the air bubbles.)
6. Use the an squeegee ( credit card )to squeeze the water out from under the Graphics. Squeegee in all directions and repeat several times. This process removes air & water from under the Graphics.
7. Let the Graphics dry completely. The amount of time needed to dry depends on the temperature and the humidity. Estimated time: 80 degrees - 30 minutes, 70 degrees - 3 hours, 50 degrees - 4 to 6 hours. These are recommendations ONLY….the Graphics MUST dry prior to the next step. 60 - 70 - 80 degrees are recommended temperatures for post installation.
8. Slowly peel back the pre-mask translucent application tape; the Graphics will adhere to the boat. If the Graphics don't adhere to the boat, you didn't wait long enough for the water to dry behind the Graphics; repeat squeegee process. LET DRY.
9. Now check for any bubbles. If you find any, place a small piece of pre-mask tape over the area; squeeze to the closest edge. If you still have a small bubble you can pop it with a pin. Small bubbles will eventually disappear from the sun over time.

HELPFUL HINTS:

• On a windy day, be very careful when you peel the vinyl graphics off the backing paper.
  The Vinyl graphics are very sticky; don't let it crease.
• Spray graphics over the sticky side as you peel off wax paper.
• Do not try to install on a windy day.
• Do not attempt installation in direct sunlight on a hot day (do it in the shadow or a closed area)
• If you need to remove old painted letters, use Easy-Off oven cleaner. Please test in an inconspicuous area before using. Please wear gloves and eye protection.
• If you have any other questions, please feel free to contact us.
• NEVER APPLY DIRECT HEAT (E.G. BUFFING WHEEL, HEAT GUN, BLOW DRYER)

 

Important information

• For digitaly printed decals (Indian head decals, U.S. Flag decals and others)
• Please ask to a professional to install these decals, If possible.
• This decals needs to be clear coat for last long and also to be resistent to wax, cleaning fluids, scratching or any wear in the time. after clear coat the will look shine and smooth, also they will last longer about 7-10 years
• Some times needs heat to install them over non flat areas.
• Install only over single areas colors ,this decals are thin and if there are 2 different shades , you may see the difference underneath (Indian head tank decals).
• If you are not an expert and you just want to try to install them, is on your own risk.
• We are not responsible for inappropriate installation or use.