( 
)
Drilling spot welds to remove unibody panels such as your cowl, rear quarter panel, floor pans and wheel wells can be tedious, but it is a fairly straightforward process. This guide will help you tackle spot weld drilling like a pro. Please remember to indicate below if this guide is helpful to you!
DRILLING SPOT WELDS
TOOLS NEEDED:
Sand Paper and/or Wire BrushDrill
Pilot Drill Bit: 1/8" diameter
Spot Weld Cutter: 3/8" diameter
Heavy Oil
Hammer
Flat Metal Chisel
SPOT WELD DRILLING PROCESS:
Step 1. Locate the spot welds needing removal
This is done by looking for small, round depressions located every few inches where the body panel is attached to the vehicle. If your vehicle is severely rusted or has been painted several times, these welds can be difficult to locate. You would then need to clean the spot weld areas with sand paper or a wire brush to locate the welds. Please see our Locating Spot Welds Guide for more information.
The drill bit is pointing at the small depression/spot weld.Step 2. Using your 1/8" drill bit, drill a pilot hole through the center of each weld
A pilot hole is a centering hole for the spot weld cutter. Helpful tip: Dip the tip of your drill bit in heavy oil prior to drilling each spot weld. This will prolong the life of your drill bit.
A pilot hole is a centering hole for the spot weld cutter. Helpful tip: Dip the tip of your drill bit in heavy oil prior to drilling each spot weld. This will prolong the life of your drill bit.
This picture shows the pilot hole being drilled.Step 3. Once all pilot holes are drilled, use your spot weld cutter to drill a hole through each spot weld.
Using a specialized weld cutter minimizes the damage to the panel underneath the panel being removed. When drilling with the weld cutter, only drill deep enough to remove the desired panel. When I drill a weld, I watch the drilling area change from clean metal to light surface rust. This would indicate that I have just reached an area between the sheet metal panels. At this time, there is usually a little "poof" of rust dust. I stop at this point, since I know I have just drilled through the first panel without over-cutting the second panel.
Here is one style of weld cutter. This is a sheet metal bit, 3/8" size
Using a specialized weld cutter minimizes the damage to the panel underneath the panel being removed. When drilling with the weld cutter, only drill deep enough to remove the desired panel. When I drill a weld, I watch the drilling area change from clean metal to light surface rust. This would indicate that I have just reached an area between the sheet metal panels. At this time, there is usually a little "poof" of rust dust. I stop at this point, since I know I have just drilled through the first panel without over-cutting the second panel.
Here is one style of weld cutter. This is a sheet metal bit, 3/8" size
Here is the weld cutter at work, drilling the top layer of the spot weld.
Voila! The weld is drilled!Step 4. After all welds have been drilled, carefully use your hammer and flat chisel to separate the panels.
This is done by laying the flat edge of the chisel between the panels and gently hammering to loosen any bits of weld that were not cut by the drill.
This is done by laying the flat edge of the chisel between the panels and gently hammering to loosen any bits of weld that were not cut by the drill.
Step 5. Now that your panel is removed, you are ready for the next process. Please see our Patch Panel Installation - Unibody Panel Replacement Guide for further information.
You are on your way to spot weld drilling! I have drilled over 5,000 spot welds throughout the last 15 years and I will probably drill 5,000 more in this year alone!
If you have found this guide to be helpful, please indicate so below by voting "YES" to this guide.
Be sure to check out our other Mustang Guides for additional restoration information and helpful tips.
FastbackStack, LLC provides the hard-to-find, obsolete Mustang parts for your 1964 1/2 - 1970 Mustang restorations. With over 100,000 original items (most of which still need to be listed on eBay), we offer what no one else has! We love hearing from fellow Mustang enthusiasts and would like to extend a special invitation to you to join our exclusive group of those receiving helpful Mustang restoration tips, those learning about our newly listed RARE, ORIGINAL parts and those receiving money saving specials.
Sign up to receive Mustang restoration tips, information and special savings!
Copyright 2007: FastbackStack, LLC
Guide created: 01/28/07 (updated 10/30/09)
Thank you for voting. If your vote meets our 
